现行
IEC 61373:2026
到馆提醒
收藏跟踪
分享链接
购买正版
选择购买版本
本服务由中国标准服务网提供
电子版
英语/电子版加密PDF格式/约1分钟可下载/有水印/要装插件FileOpen/电脑需联网/限制累计3台电脑共打印5次
¥ 3,076
更多
前往中国标准服务网获取更多购买信息
支持批量购买纸质版标准
Railway applications - Rolling stock equipment - Shock and vibration tests
铁路设施.机车车辆设备.冲击和振动试验
IEC 61373:2026规定了用于铁路车辆的设备的测试项目的要求,由于铁路运行环境的性质,这些设备随后会受到振动和冲击。为了确保设备的质量是可接受的,需要对其进行合理持续时间的测试,以模拟其整个预期寿命期间的使用条件。
模拟长寿命测试可以通过多种方式实现,每种方式都有其相关的优点和缺点,以下是最常见的:
a)放大:其中振幅增加并且时基减小;
b)时间压缩:其中保留振幅历史并且减少时基(增加频率);
c)抽取:当振幅低于指定阈值时,删除历史数据的时间片。如上项a)中所述的扩增方法用于本文件中,并与条款2中提及的出版物一起使用;它定义了在铁路车辆上使用的振动测试项目时应遵循的默认测试程序。
虽然本文件主要涉及固定铁路系统上的铁路车辆,但不排除其更广泛的使用。对于在充气轮胎上运行的系统或诸如无轨电车之类的其他运输系统,其中冲击和振动的水平明显不同于在固定轨道系统上获得的那些,可以考虑特定的测试水平。在这种情况下,应根据附件A中的指南计算频谱以及冲击持续时间和振幅。
附录F提供了用户可以考虑的在充气轮胎上运行的城市车辆的功能随机振动载荷。本文件适用于单轴测试。然而,多轴测试是可能的。
本文件未对设备固定点处的锚固螺栓进行评价。
本文件旨在评估连接到车辆主体结构上的设备(以及安装在其上的部件)。不打算测试构成主体结构一部分的设备。本文件意义上的主体结构是指车体、转向架和车轴。
以下项目超出了本文件的范围:
–铁路车辆的牵引电机;
– 任何未配备电气、电子或气动元件的机械下部结构。
本文件中未规定某些特定设备的额外或特殊振动测试,例如:
a)安装在或连接到已知产生限定频率激励的物品上的设备;b)已知暴露于特定冲击和振动激励的设备,例如受电弓、鞋架或悬挂部件;
c) 拟在客户指定的特殊操作环境中使用的设备;
d) 运输和处理测试。
第三版取消并取代了2010年出版的第二版。这个版本构成了一个技术修订。
与上一版本相比,此版本包含以下重大技术变更:
a) 考虑来自机载测量和认证的特定 ASD 光谱,仅限于特定情况;
b) 将牵引电机和任何未装备电气、电子或气动装置的下部结构排除在适用范围之外;
c) 澄清测试顺序和典型测试顺序,考虑到同时进行多项测试的可能性。轴测试;
d) 在长寿命试验期间拆除设备的弹性支架(如果位于设备和主体结构之间)的建议和指导;
e)用于将设备附接到测试台的固定装置的鉴定;
f)使用测量点作为评估机械完整性的可能性的指导;
g)改变应用于功能ASD值的加速比计算方法,以获得模拟长寿命ASD值;
h)长寿命测试的持续时间可以设置为每个轴5小时至100小时,相应的加速度比(默认值)在表中指示;
i) 澄清结构完整性的概念;
j) 对设备结构件的测试豁免情况、组件测试和有限元分析的说明(新附件E);k)将类别1和类别2的ASD频谱的最低频率f1固定在5Hz作为默认值,并且将类别3的ASD频谱的最低频率f1固定在10Hz作为默认值;
l)更新用于功能随机振动测试的ASD光谱:表1、表2、表3、表4、表A.2和图6、图7、图8、图10。铁路安全和标准委员会研究计划文件“轨道车辆安装设备的振动环境”中建议进行此更新;
m) 专门讨论使用充气轮胎的城市车辆的新附件F。
IEC 61373:2026 specifies the requirements for testing items of equipment intended for use on railway vehicles which are subsequently subjected to vibrations and shock owing to the nature of railway operational environment. To gain assurance that the quality of the equipment is acceptable, it is exposed to tests of reasonable duration that simulate the service conditions seen throughout its expected life.
Simulated long-life testing can be achieved in a number of ways each having their associated advantages and disadvantages, the following being the most common:
a) amplification: where the amplitudes are increased and the time base decreased;
b) time compression: where the amplitude history is retained and the time base is decreased (increase of the frequency);
c) decimation: where time slices of the historical data are removed when the amplitudes are below a specified threshold value.
The amplification method as stated in item a) above, is used in this document and together with the publications referred to in Clause 2; it defines the default test procedure to be followed when vibration testing items for use on railway vehicles.
Whilst this document is primarily concerned with railway vehicles on fixed rail systems, its wider use is not precluded. For systems operating on pneumatic tyres, or other transportation systems such as trolleybuses, where the level of shock and vibration clearly differ from those obtained on fixed rail systems, specific test levels can be considered. In that case, the frequency spectra and the shock duration and amplitude are computed in compliance with the guidelines in Annex A.
Annex F provides the functional random vibration load that can be considered by the user for urban vehicles operating on pneumatic tyres.
This document applies to single axis testing. However, multi-axis testing is possible.
The anchoring bolts at the fixing point(s) of the equipment are not evaluated in this document.
This document is intended to evaluate equipment which is attached to the main structure of the vehicle (and components mounted thereon). It is not intended to test equipment which forms part of the main structure. Main structure in the sense of this document means car body, bogie and axle.
The following items are out of scope of this document:
– the traction motors for railway vehicles;
– any mechanical substructure not equipped with electrical, electronic or pneumatic component.
Additional or special vibration tests for some specific equipment are not specified in this document, for example:
a) equipment mounted on, or linked to, items which are known to produce defined frequency excitation;
b) equipment such as pantographs, shoegear, or suspension components which are known to be exposed to specific shock and vibration excitation;
c) equipment intended for use in special operational environments as specified by the customer;
d) transportation and handling tests.
This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) consideration of specific ASD spectra from onboard measurements and certification limited to the specific case;
b) exclusion from the scope of applicability of traction motors and any substructure not equipped with electrical, electronic or pneumatic device;
c) clarification for order of testing and typical test sequence, taking into account the possibility of simultaneous multi-axis testing;
d) recommendation and guidance for removing resilient mounts of the equipment (if located between the equipment and the main structure) during the long-life test;
e) qualification of the fixture device used to attach the equipment to the test bench;
f) guidance for using a measuring point as a possibility to assess mechanical integrity;
g) change of the method to calculate the acceleration ratio which shall be applied to the functional ASD value to obtain the simulated long-life ASD value;
h) duration of long-life test can be set from 5 h to 100 h per axis, with corresponding acceleration ratio (default value) indicated in a table;
i) clarification of the concept of structural integrity;
j) description of test exemption cases, subassembly tests, and finite element analysis for structural parts of equipment (new Annex E);
k) the lowest frequency f1 of ASD spectra of Category 1 and Category 2 is fixed at 5 Hz as a default value, and the lowest frequency f1 of ASD spectra of Category 3 is fixed at 10 Hz as a default value;
l) update of ASD spectra for functional random vibration test: Table 1, Table 2, Table 3, Table 4, Table A.2 and Figure 6, Figure 7, Figure 8, Figure 10. This update was recommended in the Rail Safety and Standard Board research program document: “Vibration environment for rail vehicle mounted Equipment”;
m) new annex F dedicated on urban vehicle operating on pneumatic tyres.