首页 馆藏资源 标准快讯 标准数字化 呈缴征集 标准服务 关于我们
现行 ASTM F712-26
到馆提醒
收藏跟踪
购买正版
Standard Test Methods and Specifications for Electrically Insulating Plastic Guard Equipment for Protection of Workers 用于保护工人的电绝缘塑料防护设备的标准测试方法和规范
发布日期: 2026-09-01
1.1 这些测试方法包括对塑料防护装置和组装防护装置系统的电气测试。它们是: 1.1.1 耐压测试,以及 1.1.2 闪络电压。 1.1.3 这些规范涵盖了工人用于电力电路临时绝缘的塑料防护设备和防护系统。 1.1.4 这些规范涵盖的塑料防护设备仅额定用于瞬时或刷子接触。最大使用电压包括在 表1 和 表2 . 1.2 这些测试涵盖但不限于以下典型防护: 1.2.1 导体护罩和连接盖如下: 1.2.1.1 线警卫, 1.2.1.2 线路保护连接器, 1.2.1.3 绝缘体盖, 1.2.1.4 死角封面, 1.2.1.5 公共汽车警卫,以及 1.2.1.6 公交车“T”警卫。 1.2.2 结构和设备覆盖如下:1.2.2.1 杆卫, 1.2.2.2 脊销盖, 1.2.2.3 开关刀片盖, 1.2.2.4 护臂, 1.2.2.5 切口盖, 1.2.2.6 结构障碍,以及 1.2.2.7 交叉臂护板。 1.3 该设备的用户通常会准备正确使用和维护的说明。 1.4 该设备的使用和维护超出了这些测试方法的范围。 1.5 以英寸磅为单位的数值应被视为标准值。括号中给出的值是对国际单位制单位的数学换算,仅供参考,不被认为是标准的。 1.6 本标准无意解决与其使用相关的所有安全问题(如果有的话)。本标准的使用者有责任在使用前建立适当的安全、健康和环境实践,并确定法规限制的适用性。1.7 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。 = 意义和用途 ===== 4.1 所有测试均可用于产品设计鉴定。 4.2 本规范涵盖了制造商指定的最低电气、化学和物理性能,以及确定这些性能的详细程序。买方可以选择执行或已经执行了任何这些测试,并可以拒绝不符合标准标准的设备。关于不符合质量标准的索赔有待制造商核实。4.3 塑料防护设备用于防止工人意外接触电刷。在使用它们的最大电压和测试它们的验证测试电压之间应提供安全裕度。这种关系显示在 表1 和 表2 该设备设计仅用于相对地或覆盖相对覆盖相曝光。 附注1: 橡胶绝缘设备实际上仅限于设计规范标准中的4类材料。塑料防护装置的设计超越了这些电压,并提供了令人满意的工人保护程度。橡胶和塑料防护装置在使用标准上存在重大差异。每个橡胶绝缘设备的手套、套筒或其他物品都有一个给定的相位安全系数。可以使用它的两相电压和测试它的等级或验证电压。然而,塑料防护设备的设计仅在相对地暴露中使用时才提供令人满意的安全系数。如果暴露是相间暴露,则只有当暴露是覆盖相间暴露时,才能提供令人满意的安全系数。 4.4 工作实践因用户而异,取决于许多因素。这些可以包括但不限于操作系统电压、结构设计、工作规程技术、天气条件等。因此,除因设计限制而在本说明书中规定的限制外,本设备的使用和维护超出了本说明书的范围。 4.5 这种类型的防护设备的用户通常有责任准备完整的说明和法规,以详细管理这种设备的正确和安全使用。
1.1 These test methods cover electrical tests on plastic guards and assembled guard systems. They are: 1.1.1 Withstand voltage proof test, and 1.1.2 Flashover voltage. 1.1.3 These specifications cover plastic guard equipment and guard systems used by workers for temporary insulation on electric power circuits. 1.1.4 Plastic guard equipment covered by these specifications is rated for momentary, or brush contact only. Maximum-use voltages are covered in Table 1 and Table 2 . 1.2 These tests cover, but are not limited to, the following typical guards: 1.2.1 Conductor Guards and Connecting Covers as Follows: 1.2.1.1 Line guards, 1.2.1.2 Line guard connectors, 1.2.1.3 Insulator covers, 1.2.1.4 Dead-end covers, 1.2.1.5 Bus guards, and 1.2.1.6 Bus “T” guards. 1.2.2 Structure and Apparatus Covers as Follows: 1.2.2.1 Pole guards, 1.2.2.2 Ridge pin covers, 1.2.2.3 Switch blade covers, 1.2.2.4 Arm guards, 1.2.2.5 Cutout covers, 1.2.2.6 Structural barriers, and 1.2.2.7 Cross arm guard. 1.3 It is common practice for the user of this equipment to prepare instructions for the correct use and maintenance. 1.4 The use and maintenance of this equipment is beyond the scope of these test methods. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 4.1 All tests may be used for product design qualification. 4.2 This specification covers the minimum electrical, chemical, and physical properties designated by the manufacturer and the detailed procedures by which such properties are to be determined. The purchaser has the option to perform or have performed any of these tests and may reject equipment that fails to meet the standard criteria. Claims concerning failure to meet the specification are subject to verification by the manufacturer. 4.3 Plastic guard equipment is used for protection against accidental brush contact by the worker. A margin of safety shall be provided between the maximum voltage at which they are used and the proof-test voltage at which they are tested. This relationship is shown in Table 1 and Table 2 . The equipment is designed only for phase-to-ground or covered phase-to-covered-phase exposure. Note 1: Rubber insulating equipment is realistically limited to Class 4 material in the design specification standards. Plastic guard equipment has been designed to go beyond these voltages and provide a satisfactory degree of worker protection. Major differences exist in use criteria between the rubber and the plastic guard equipment. Each glove, sleeve, or other article of rubber insulating equipment has a given safety factor for the phase-to-phase voltage on which it may be used and the class or proof voltage at which it is tested. Plastic guard equipment, however, is designed to provide a satisfactory safety factor only when used in a phase-to-ground exposure. If exposure is phase-to-phase, then a satisfactory safety factor is only provided if the exposure is covered-phase-to-covered-phase. 4.4 Work practices vary from user to user, dependent upon many factors. These may include, but are not limited to, operating system voltages, construction design, work procedure techniques, weather conditions, etc. Therefore, except for the restrictions set forth in this specification because of design limitations, the use and maintenance of this equipment is beyond the scope of this specification. 4.5 It is common practice and the responsibility of the user of this type of protective equipment to prepare complete instructions and regulations to govern in detail the correct and safe use of such equipment.
分类信息
关联关系
研制信息
归口单位: F18.25
相似标准/计划/法规
现行
ASTM D117-22
Standard Guide for Sampling, Test Methods, and Specifications for Electrical Insulating Liquids
电绝缘液体取样、试验方法和规范的标准指南
2022-05-01
现行
ASTM D1169-19a
Standard Test Method for Specific Resistance (Resistivity) of Electrical Insulating Liquids
电绝缘液体比电阻(电阻率)的标准试验方法
2019-10-01
现行
ASTM D3394-16(2022)
Standard Test Methods for Sampling and Testing Electrical Insulating Board
电气绝缘板取样和试验的标准试验方法
2022-05-01
现行
ASTM D4733-24
Standard Test Methods for Solventless Electrical Insulating Varnishes
无溶剂电绝缘漆的标准测试方法
2024-12-01
现行
ASTM D374/D374M-23
Standard Test Methods for Thickness of Solid Electrical Insulation
固体电绝缘厚度的标准试验方法
2023-10-01
现行
BS EN 50289-1-4-2001
Communication cables. Specifications for test methods. Electrical test methods-Insulation resistance
通讯电缆 试验方法规范 电气试验方法
2001-09-15
现行
ANSI/NEMA C29.1-2018
American National Standard for Electrical Power Insulators--Test Methods
美国电力绝缘子国家标准试验方法
2018-05-01
现行
GB/T 25961-2010
电气绝缘油中腐蚀性硫的试验法
Standard test method for corrosive sulfur in electrical insulating oils
2011-01-10
现行
ASTM D5638-18(2025)
Standard Test Method for Chemical Resistance of Electrical Insulating Varnishes
电绝缘漆耐化学性的标准试验方法
2025-09-01
现行
ASTM D2305-18
Standard Test Methods for Polymeric Films Used for Electrical Insulation
用于电绝缘的聚合物薄膜的标准试验方法
2018-05-01
现行
ASTM D2756-24
Standard Test Method for Weight Loss of Electrical Insulating Varnishes
电绝缘清漆重量损失的标准试验方法
2024-12-01
现行
ASTM D5637-24
Standard Test Method for Moisture Resistance of Electrical Insulating Varnishes
电绝缘清漆耐湿性的标准试验方法
2024-12-01
现行
ASTM D619-21
Standard Test Methods for Vulcanized Fibre Used for Electrical Insulation
用于电绝缘的硫化纤维的标准试验方法
2021-01-01
现行
ASTM D1304-99(2020)e1
Standard Test Methods for Adhesives Relative to Their Use as Electrical Insulation
粘合剂相对于电绝缘使用的标准试验方法
2020-01-01
现行
ASTM D2225-20
Standard Test Methods for Silicone Liquids Used for Electrical Insulation
电绝缘用硅液体的标准试验方法
2020-11-01
现行
ASTM D1275-24
Standard Test Method for Corrosive Sulfur in Electrical Insulating Liquids
电绝缘液体中腐蚀性硫的标准试验方法
2024-01-15
现行
ASTM D352-23
Standard Test Methods for Pasted Mica Used in Electrical Insulation
电绝缘用粘贴云母的标准试验方法
2023-08-01
现行
SH/T 0792-2007
电器绝缘油中2,6-二叔丁基对甲酚和2,6-二叔丁基苯酚含量测定法(红外吸收光谱法)
Standard test method for 2,6-di-tert-butyl-p-cresol and 2,6-di-tert-butyl phenol in electrical insulating oil by infrared absorption
2007-08-01
现行
ASTM D3376-25
Standard Test Methods of Sampling and Testing Pulps to be Used in the Manufacture of Electrical Insulation
采样和测试用于制造电气绝缘的纸浆的标准测试方法
2025-12-01
现行
ASTM D202-23
Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation
电绝缘用未处理纸的取样和试验的标准试验方法
2023-05-01