首页 馆藏资源 标准快讯 标准数字化 呈缴征集 标准服务 关于我们
现行 ASTM D5527-23
到馆提醒
收藏跟踪
购买正版
Standard Practices for Measuring Surface Wind and Temperature by Acoustic Means 用声学方法测量表面风和温度的标准实施规程
发布日期: 2023-09-01
1.1 这些实践包括通过采用逆时间测量技术的商用声波风速计/温度计测量一维、二维或三维矢量风分量和声波温度的程序。这些实践适用于使用安装在固定塔架上的仪器测量水平地形上的风速分量。这些实践也适用于转换为音速的声速测量,但不适用于使用辅助温度设备的温度测量。 1.2 以国际单位制表示的数值应视为标准。 本标准中不包括其他计量单位。 1.3 本标准并非旨在解决与其使用相关的所有安全问题(如有)。本标准的使用者有责任在使用前制定适当的安全、健康和环境实践,并确定监管限制的适用性。 1.4 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。 ===意义和用途====== 5.1 声波风速计/温度计用于测量大气中的湍流成分,但在密闭区域和非常靠近地面的区域除外。这些实践适用于使用这些仪器对风、声波温度和大气湍流成分进行现场测量。准瞬时速度分量测量值在用户选择的采样时间上取平均值,以定义沿轴风分量的平均值、平均风速和方向,以及单个分量或分量组合的方差或协变,或两者。 协方差用于涡相关研究和边界层热通量和动量通量的计算。声波风速计/温度计提供了表征湍流大气边界层状态所需的数据。 5.2 声波风速计/温度计阵列应具有足够高的结构刚度和足够低的热膨胀系数,以将内部对准保持在±0.1°以内。系统电子设备必须在其工作温度范围内保持稳定;时间计数器振荡器的不稳定性不得超过0.01 % 频率。 有关内部对准验证程序,请咨询传感器制造商。 5.3 这些实践中提供的计算和转换适用于正交阵列。还提供了对常见类型的非正交阵列的参考。
1.1 These practices cover procedures for measuring one-, two-, or three-dimensional vector wind components and sonic temperature by means of commercially available sonic anemometer/thermometers that employ the inverse time measurement technique. These practices apply to the measurement of wind velocity components over horizontal terrain using instruments mounted on stationary towers. These practices also apply to speed of sound measurements that are converted to sonic temperatures but do not apply to the measurement of temperature using ancillary temperature devices. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 Sonic anemometer/thermometers are used to measure turbulent components of the atmosphere except in confined areas and very close to the ground. These practices apply to the use of these instruments for field measurement of the wind, sonic temperature, and atmospheric turbulence components. The quasi-instantaneous velocity component measurements are averaged over user-selected sampling times to define mean along-axis wind components, mean wind speed and direction, and the variances or covariances, or both, of individual components or component combinations. Covariances are used for eddy correlation studies and for computation of boundary layer heat and momentum fluxes. The sonic anemometer/thermometer provides the data required to characterize the state of the turbulent atmospheric boundary layer. 5.2 The sonic anemometer/thermometer array shall have a sufficiently high structural rigidity and a sufficiently low coefficient of thermal expansion to maintain an internal alignment to within ±0.1°. System electronics must remain stable over its operating temperature range; the time counter oscillator instability must not exceed 0.01 % of frequency. Consult with the sensor manufacturer for an internal alignment verification procedure. 5.3 The calculations and transformations provided in these practices apply to orthogonal arrays. References are also provided for common types of non-orthogonal arrays.
分类信息
关联关系
研制信息
归口单位: D22.11
相似标准/计划/法规