首页 馆藏资源 标准快讯 标准数字化 呈缴征集 标准服务 关于我们
作废 ASTM D4630-96(2008)
到馆提醒
收藏跟踪
购买正版
Standard Test Method for Determining Transmissivity and Storage Coefficient of Low-Permeability Rocks by In Situ Measurements Using the Constant Head Injection Test (Withdrawn 2017) 通过使用恒压头注射试验的现场测量确定低渗透性岩石的渗透率和储存系数的标准测试方法(撤回2017年)
发布日期: 2008-09-15
废止日期: 2017-03-30
1.1本试验方法涵盖了确定渗透率低于10的地质构造的透射率和储能率的现场程序 − 3. μ m 2. (1毫达西)使用恒定头部注射。 1.2如果测试间隔代表整个区域,且围岩完全浸水,则通过本测试方法确定的透射率和储水率值可很好地近似表示相关区域的输水能力。 1.3以国际单位制表示的数值应视为标准值。本标准不包括其他计量单位。 1.4 本标准并非旨在解决与其使用相关的所有安全问题(如有)。本标准的用户有责任在使用前制定适当的安全和健康实践,并确定监管限制的适用性。 ====意义和用途====== 试验方法 — 恒压注入试验方法用于确定充填层周围低渗透地层的透过率和储能率。该方法的优点是:( 1. )它避免了井筒储存的影响( 2. )它可以用于广泛的岩体渗透性,以及( 3. )与在渗透性更强的岩石中使用的传统泵和段塞试验相比,它的持续时间要短得多。 分析 — 通过Jacob和Lohman描述的曲线匹配技术,评估使用建议试验方法获得的瞬态水流量数据 (1) 并扩展到Doe对单个裂缝的分析 等 (2). 如果水流量达到稳定状态,则可用于计算试验间隔的透过率 (3). 单位 : 转换 — 地层渗透率通常用单位达西表示。当粘度为1 cp(1 mPa)的流体时,多孔介质的渗透率为1达西 · s) 以1厘米的速度流过 3. /s(10 − 6米 3. /s) /1厘米 2. (10 − 4米 2. )压差为1 atm(101.4 kPa)/1 cm(10 mm)长度时的横截面积。一个达西对应于0.987 μ m 2. . 对于20℃时作为流动流体的水 ° C、 导水率为9.66 μ m/s对应于1达西的磁导率。
1.1 This test method covers a field procedure for determining the transmissivity and storativity of geological formations having permeabilities lower than 10 − 3 μ m 2 (1 millidarcy) using constant head injection. 1.2 The transmissivity and storativity values determined by this test method provide a good approximation of the capacity of the zone of interest to transmit water, if the test intervals are representative of the entire zone and the surrounding rock is fully water-saturated. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ====== Significance And Use ====== Test Method — The constant pressure injection test method is used to determine the transmissivity and storativity of low-permeability formations surrounding packed-off intervals. Advantages of the method are: ( 1 ) it avoids the effect of well-bore storage, ( 2 ) it may be employed over a wide range of rock mass permeabilities, and ( 3 ) it is considerably shorter in duration than the conventional pump and slug tests used in more permeable rocks. Analysis — The transient water flow rate data obtained using the suggested test method are evaluated by the curve-matching technique described by Jacob and Lohman (1) and extended to analysis of single fractures by Doe et al. (2). If the water flow rate attains steady state, it may be used to calculate the transmissivity of the test interval (3). Units : Conversions — The permeability of a formation is often expressed in terms of the unit darcy. A porous medium has a permeability of 1 darcy when a fluid of viscosity 1 cp (1 mPa · s) flows through it at a rate of 1 cm 3 /s (10 − 6 m 3 /s)/1 cm 2 (10 − 4 m 2 ) cross-sectional area at a pressure differential of 1 atm (101.4 kPa)/1 cm (10 mm) of length. One darcy corresponds to 0.987 μ m 2 . For water as the flowing fluid at 20 ° C, a hydraulic conductivity of 9.66 μ m/s corresponds to a permeability of 1 darcy.
分类信息
关联关系
研制信息
归口单位: D18.21
相似标准/计划/法规
现行
ASTM D4630-19
Standard Test Method for Determining Transmissivity and Storage Coefficient of Low-Permeability Rocks by In Situ Measurements Using the Constant Head Injection Test
用恒定压头注入试验现场测量法测定低渗透岩石的透射率和储存系数的标准试验方法
2019-02-01
现行
ASTM D4106-20
Standard Practice for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Nonleaky Confined Aquifers by the Theis Nonequilibrium Method
用Theis非平衡法测定无渗漏承压含水层的透射率和储存系数的标准实施规程(分析程序)
2020-06-01
现行
ASTM D4105/D4105M-20
Standard Practice for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Nonleaky Confined Aquifers by the Modified Theis Nonequilibrium Method
用改进的Theis非平衡法测定无渗漏承压含水层的透射率和储存系数的标准实施规程(分析程序)
2020-05-15
现行
ASTM E96/E96M-24a
Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
重量法测定材料水蒸气透过率的标准试验方法
2024-11-01
现行
ASTM D6574/D6574M-13(2021)
Standard Test Method for Determining the (In-Plane) Hydraulic Transmissivity of a Geosynthetic by Radial Flow
标准测试方法
2021-05-01
现行
ASTM D7603-23
Standard Test Method for Determination of Storage Stability and Compatibility in Automotive Gear Oils
汽车齿轮油储存稳定性和兼容性测定的标准试验方法
2023-03-01
现行
ASTM D5855/D5855M-20
Standard Practice for (Analytical Procedure) Determining Transmissivity and Storage Coefficient of Confined Nonleaky or Leaky Aquifer by Constant Drawdown Method in Flowing Well
用流动井中的恒定水位下降法测定承压非渗漏或渗漏含水层的导水率和蓄水系数的标准实施规程
2020-05-15
现行
ASTM D6701-24
Standard Test Method for Determining Water Vapor Transmission Rates Through Nonwoven and Plastic Barriers
测定通过无纺织物和塑料屏障的水蒸气透过率的标准试验方法
2024-05-01
现行
ASTM D4631-18
Standard Test Method for Determining Transmissivity and Storativity of Low Permeability Rocks by In Situ Measurements Using Pressure Pulse Technique
用压力脉冲技术现场测量测定低渗透性岩石的透射率和贮存率的标准试验方法
2018-07-15
现行
GB/T 38074-2019
手动变速箱润滑油摩擦磨损性能的测定 SRV试验机法
Standard test method for determining the friction and wear properties of manual transmission fluid using a high-frequency—Linear-oscillation(SRV)test machine
2019-10-18
现行
ASTM D4716/D4716M-22
Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
用恒定水头测定土工合成材料单位宽度(平面内)流率和液压透射率的标准试验方法
2022-05-01
现行
ASTM D6281-23
Standard Test Method for Airborne Asbestos Concentration in Ambient and Indoor Atmospheres as Determined by Transmission Electron Microscopy Direct Transfer (TEM)
用透射电子显微镜直接传输(TEM)测定环境和室内大气中空气中石棉浓度的标准试验方法
2023-09-01
现行
ASTM D8210-22
Standard Test Method for Automatic Determination of Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants Using a Rotational Viscometer
用旋转粘度计自动测定自动变速器油、液压油和润滑剂低温粘度的标准试验方法
2022-07-01
现行
ASTM D8227-20(2025)
Standard Test Method for Determining the Coefficient of Friction of Synchronizer Lubricated by Mechanical Transmission Fluids (MTF) Using a High-Frequency, Linear-Oscillation (SRV) Test Machine
用高频线性振荡(SRV)试验机测定机械传动液(MTF)润滑的同步器摩擦系数的标准试验方法
2025-04-01
现行
ASTM D7806-26
Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Ester) and Triglyceride Content in Diesel Fuel Using Mid-Infrared Spectroscopy (FTIR Transmission Method)
用中红外光谱法(FTIR透射法)测定柴油中生物柴油(脂肪酸甲酯)和甘油三酯含量的标准试验方法
2026-05-01
现行
ASTM E2321-03(2019)
Standard Practice for Use of Test Methods for Determining the Water Vapor Transmission (WVT) of Exterior Insulation and Finish Systems (EIFS)
测定外部绝缘和表面处理系统(EIF)的水蒸气传输(WVT)的试验方法使用的标准实施规程
2019-04-01
现行
ASTM F1927-20
Standard Test Method for Determination of Oxygen Gas Transmission Rate, Permeability and Permeance at Controlled Relative Humidity Through Barrier Materials Using a Coulometric Detector
用库仑检测器测定在受控相对湿度下通过阻挡材料的氧气传输速率、渗透性和渗透性的标准试验方法
2020-06-01
现行
ASTM D8526-23
Standard Test Method for Analytical Procedure Using Transmission Electron Microscopy for the Determination of the Concentration of Carbon Nanotubes and Carbon Nanotube-containing Particles in Ambient Atmospheres
使用透射电子显微镜测定环境大气中碳纳米管和含碳纳米管颗粒浓度的分析程序的标准试验方法
2023-09-01
现行
ASTM F2476-24
Standard Test Method for the Determination of Carbon Dioxide Gas Transmission Rate (CO2TR) Through Barrier Materials Using an Infrared Detector
用红外线检测器测定二氧化碳气体透过阻隔材料的速率(CO2TR)的标准试验方法
2024-12-15
现行
GOST R ISO 12127-2-2011
Система стандартов безопасности труда. Одежда для защиты от тепла и пламени. Определение контактной теплопередачи через защитную одежду или составляющие ее материалы. Часть 2. Метод испытаний с использованием контактного тепла нагретого падающего маленького цилиндра
职业安全标准体系 防热和火焰防护服 通过防护服或构成材料测定接触热传递 第2部分使用滴下小气瓶产生的接触热测试方法