首页 馆藏资源 标准快讯 标准数字化 呈缴征集 标准服务 关于我们
现行 ASTM E1232-07(2019)
到馆提醒
收藏跟踪
购买正版
Standard Test Method for Temperature Limit of Flammability of Chemicals 化学品可燃性温度极限的标准试验方法
发布日期: 2019-02-01
1.1 本试验方法包括测定与液体(或固体)化学品平衡的蒸汽在大气压力下充分浓缩以在空气中形成易燃混合物的最低温度。本试验方法专门用于测定使用空气作为氧化剂和稀释剂来源的系统的可燃性温度极限。它也可用于其他氧化剂/稀释剂组合,包括空气和稀释剂混合物;但是,不应使用比空气强度更强的氧化剂/稀释剂组合。此外,不应测试能够发生爆炸性分解反应的不稳定化学品(参见 8.3 ). 1.2 本试验方法设计和编写为在当地环境压力下运行,最大初始压力限制为1 atm abs。 它也可用于减压,实际压力下限约为13.3 kPa(100 mm Hg)。该设备的最高实际工作温度约为150°C(302°F)( 注释A1.2 ). 1.3 以国际单位制表示的数值应视为标准值。括号中给出的值是英寸-磅单位的数学转换,仅供参考,不被视为标准值。 1.4 本标准应用于测量和描述受控实验室条件下材料、产品或组件对热量和火焰的响应特性,不应用于描述或评估实际火灾条件下材料、产品或组件的火灾危险或火灾风险。然而,该测试结果可作为火灾风险评估的要素,该评估考虑了与特定最终用途火灾危险评估相关的所有因素。 1.5 本标准并非旨在解决与其使用相关的所有安全问题(如有)。本标准的用户有责任在使用前制定适当的安全、健康和环境实践,并确定监管限制的适用性。 第节给出了具体的安全预防措施 8. . 1.6 本国际标准是根据世界贸易组织技术性贸易壁垒(TBT)委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 5.1 可燃性的下限温度是液体(或固体)化学品在平衡条件下形成足够蒸汽与空气形成易燃混合物的最低温度。 了解该温度对于确定化学品安全处理指南非常重要,尤其是在密闭过程和储存容器中。 注1: 由于闪点装置和程序中固有的物理因素,闭杯闪点温度不一定是化学品释放易燃蒸汽的最低温度(见 附录X2 和 附录X3 ,部分取自试验方法 E502型 ). 可燃性试验的温度限制旨在补充闪点试验固有的限制( 附录X2 ). 在化学加工行业中,如在封闭的工艺和储存容器中,其结果接近于平衡情况下易燃蒸汽形成的最低温度。 注2: 由于在标准封闭环境中测试时存在火焰淬火效应- 杯式闪点仪,某些化学品没有闪点,但会产生蒸汽,在足够大的容器中传播火焰( X3.2 ). 易燃性试验箱的温度极限足够大,以克服大多数实际情况下的火焰熄灭效应,因此,如果确实存在气相易燃性,通常表明存在气相易燃性( 6.2 ). 注3: 可燃性下限(LTL)只是应评估的几个特征之一,以确定特定应用中特定材料的安全性。例如,通过本试验方法发现一些材料具有LTL,而事实上,在整体易燃性评估中还应考虑其他特性,如最小点火能量和燃烧热。 5.2 易燃性下限下的蒸汽浓度等于通过试验方法测量的易燃下限浓度 E681 并推回相同的温度。(如果可用可燃性数据的蒸汽压和浓度极限,则可以估计可燃性的温度下限( A2.3 ). 因此,比较测试结果可以检查测试可靠性、蒸汽压数据的可靠性或两者。)
1.1 This test method covers the determination of the minimum temperature at which vapors in equilibrium with a liquid (or solid) chemical will be sufficiently concentrated to form flammable mixtures in air at atmospheric pressure. This test method is written specifically for determination of the temperature limit of flammability of systems using air as the source of oxidant and diluent. It may also be used for other oxidant/diluent combinations, including air plus diluent mixtures; however, no oxidant/diluent combination stronger than air should be used. Also, no unstable chemical capable of explosive decomposition reactions should be tested (see 8.3 ). 1.2 This test method is designed and written to be run at local ambient pressure and is limited to a maximum initial pressure of 1 atm abs. It may also be used for reduced pressures with the practical lower pressure limit being approximately 13.3 kPa (100 mm Hg). The maximum practical operating temperature of this equipment is approximately 150°C (302°F) ( Note A1.2 ). 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.4 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions, and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific safety precautions are given in Section 8 . 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 The lower temperature limit of flammability is the minimum temperature at which a liquid (or solid) chemical will evolve sufficient vapors to form a flammable mixture with air under equilibrium conditions. Knowledge of this temperature is important in determining guidelines for the safe handling of chemicals, particularly in closed process and storage vessels. Note 1: As a result of physical factors inherent in flash point apparatus and procedures, closed-cup flash point temperatures are not necessarily the minimum temperature at which a chemical will evolve flammable vapors (see Appendix X2 and Appendix X3 , taken in part from Test Method E502 ). The temperature limit of flammability test is designed to supplement limitations inherent in flash point tests ( Appendix X2 ). It yields a result closely approaching the minimum temperature of flammable vapor formation for equilibrium situations in the chemical processing industry such as in closed process and storage vessels. Note 2: As a result of flame quenching effects existing when testing in standard closed-cup flash point apparatus, there are certain chemicals that exhibit no flash point but do evolve vapors that will propagate a flame in vessels of adequate size ( X3.2 ). The temperature limit of flammability test chamber is sufficiently large to overcome flame quenching effects in most cases of practical importance, thus, usually indicating the presence of vapor-phase flammability if it does exist ( 6.2 ). Note 3: The lower temperature limit of flammability (LTL) is only one of several characteristics that should be evaluated to determine the safety of a specific material for a specific application. For example, some materials are found to have an LTL by this test method when, in fact, other characteristics such as minimum ignition energy and heat of combustion should also be considered in an overall flammability evaluation. 5.2 The vapor concentration present at the lower temperature limit of flammability equals the lower flammable limit concentration as measured by Test Method E681 and extrapolated back to the same temperature. (This permits estimation of lower temperature limits of flammability if vapor pressure and concentration limit of flammability data are available ( A2.3 ). A comparison of results of the tests, thus, affords a check on test reliability, the reliability of vapor pressure data, or both.)
分类信息
关联关系
研制信息
归口单位: E27.04
相似标准/计划/法规
现行
ASTM E918-19
Standard Practice for Determining Limits of Flammability of Chemicals at Elevated Temperature and Pressure
确定化学品在高温和高压下易燃性极限的标准实践
2019-12-01
现行
GB/T 21844-2008
化合物(蒸气和气体)易燃性浓度限值的标准试验方法
Standard test method for concentration limits of flammability of chemicals (vapors and gases)
2008-05-12
现行
ASTM E681-09(2023)
Standard Test Method for Concentration Limits of Flammability of Chemicals (Vapors and Gases)
化学品(蒸气和气体)可燃性浓度限值的标准试验方法
2023-05-01
现行
ASTM E659-24
Standard Test Method for Autoignition Temperature of Chemicals
化学品自燃温度的标准试验方法
2024-10-01
现行
ASTM E487-20
Standard Test Methods for Constant-Temperature Stability of Chemical Materials
化学材料恒温稳定性的标准试验方法
2020-02-01
现行
ASTM D8503-23
Standard Test Method for Determining the Scuffing Temperature Limit of Lubricating Oils Using the SRV Test Machine
使用SRV试验机测定润滑油剥落温度极限的标准试验方法
2023-03-01
现行
ASTM E1473-22
Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
镍、钴和高温合金化学分析的标准试验方法
2022-11-15
现行
ASTM E354-25
Standard Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys
高温 电 磁和其他类似铁 镍和钴合金化学分析的标准测试方法
2025-11-15
现行
GOST R 12.4.297-2013
Система стандартов безопасности труда. Одежда специальная для защиты от повышенных температур теплового излучения, конвективной теплоты, выплесков расплавленного металла, контакта с нагретыми поверхностями, кратковременного воздействия пламени. Технические требования и методы испытаний
职业安全标准体系 用于防止高温辐射 对流热 金属熔融飞溅 接触热 有限的火焰蔓延的服装 技术要求和试验方法