船用起重机的索具主要是钢丝绳索具。本文件规定了技术要求 钢丝绳用行走索具和站立索具的选择和应用要求 船用起重机的绳索索具。BS ISO 19360:2016规定了混凝土的容许强度和性能水平的最低要求 船用起重机的钢丝绳应符合起重机的设计、使用和维护要求。本文件规定了安装、维护、检查和维护的实施标准 船用起重机运行索具和固定索具的废弃品。本文件适用于以下类型的船用起重机:安装在船舶上的甲板起重机，用于在港口或遮蔽水域装卸货物或集装箱 条件安装在驳船或浮筒上的浮式起重机或抓斗起重机，用于在港口条件下操作 或保护水环境；安装在船舶（包括浮动码头）上的机舱起重机和供应起重机等 港口条件下的装卸设备和仓库。 本文件不适用于以下情况:事故或碰撞产生的荷载；海平面以下的起重作业；应包括在船舶类别中且船舶接收的起重机 起重机类符号；但是，本文件的内容可作为建议或参考使用 指导其他可能被考虑在范围内的项目不在此列 文件，如空套项目，如钩块、支架和配件；被阶级社会列入阶级的起重机； 最低环境工作温度不低于-20℃；最高环境工作温度高于+45°C；起重机的运输、组装、拆卸和退役；起重配件，即起重机和负载之间的任何物品；涉及多台起重机的起重作业；手动起重机；紧急救援操作交叉参考:ISO 4309:2010ISO 2408ISO 3828ISO 4306-1ISO 16625ISO 17893ISO 19354ASME B30。8:2010API 2C:2012购买本文件时可获得的所有现行修订均包含在购买本文件中。

Rigging used for marine cranes is mainly wire rope rigging. This document specifies the technical requirements of the selection and application of running rigging and standing rigging used for wire rope rigging of marine cranes.BS ISO 19360:2016 specifies the minimum requirements of the allowable strength and performance level for wire ropes of marine cranes according to the design, application and maintenance requirements of cranes.This document specifies the implementation criteria of installation, maintenance, inspection and discards for running rigging and standing rigging of marine cranes.This document is applicable to the following types of marine crane:deck cranes mounted on ships for handling cargo or containers in harbour or sheltered water conditions;floating cranes or grab cranes mounted on barges or pontoons for operating in harbour conditions or sheltered water conditions;engine room cranes and provision cranes, etc. mounted on ships (including floating docks) for handling equipment and stores in harbour conditions.This document does not apply to the following:loads from accidents or collisions;lifting operations below sea level;cranes which are supposed to be included in the class of the vessel and where the vessel receives a crane class notation; the contents of this document may be used however, as recommendation or guidance;other items where there is the danger that they might be considered in-scope are excluded from this document, such asloose gear items, such as the hook block, andropes and fittings;cranes which are to be included in class by the class society;minimum ambient operating temperatures no less than -20 °C;maximum ambient operating temperatures above +45 °C;transport, assembly, dismantling and decommissioning of cranes;lifting accessories, i.e. any item between the crane and the load;lifting operations involving more than one crane;hand powered cranes;emergency rescue operationsCross References:ISO 4309:2010ISO 2408ISO 3828ISO 4306-1ISO 16625ISO 17893ISO 19354ASME B30.8:2010API 2C:2012All current amendments available at time of purchase are included with the purchase of this document.