首页 馆藏资源 标准快讯 标准数字化 呈缴征集 标准服务 关于我们
现行 ASTM D2321-26
到馆提醒
收藏跟踪
购买正版
Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications 下水道和其他重力流应用热塑性管的地下安装的标准实施规程
发布日期: 2026-05-01
1.1 本规范为下水道和其他重力流应用中使用的埋地热塑性管道的安装提供了建议。这些建议旨在确保热塑性管道在各种使用条件下具有稳定的地下环境。然而,由于可获得的许多柔性塑料管产品和自然地面条件的固有可变性,实现任何一种产品的令人满意的性能可能需要修改本文中包含的规定以满足特定的项目要求。 1.2 本规范的范围必然不包括产品性能标准,如最小管道刚度、最大使用挠度或长期强度。因此,产品制造商、规范者或项目工程师有责任验证并确保为预期应用指定的管道,当根据本实施例中概述的程序安装时,将提供长期、令人满意的pe根据为该应用建立的标准进行性能。对实现满意安装的重要因素的评论包含在 附录X1 . 附注1: 附录中的具体段落在本实践的正文中引用,以供参考。 附注2: 以下ASTM标准可与本实践相关联:实践 D420 、试验方法 D1556/D1556M 、方法 D2216 ,规格 D2235 、试验方法 D2412 ,规格 D2564 、实践 D2657 、实践 D2855 、试验方法 D2922 、试验方法 D3017 、实践 F402 ,规格 F477 ,规格 F545 ,和规格 F913 . 附注3: 大多数管道规范和一些建筑规范都有安装地下“建筑排水管和建筑下水道”的规定。查看它们的管道应用。1.3 单位- 以SI单位或英寸-磅单位表示的值应单独视为标准值。每个系统中陈述的值不一定完全等同;因此,为确保符合标准,每个系统应独立使用,两个系统的数值不得合并使用。 1.4 本标准并不旨在解决与其使用相关的所有安全性问题(如果有)。本标准的使用者有责任在使用前建立适当的安全、健康和环境实践并确定法规限制的适用性。 1.5 本国际标准是根据世界贸易组织技术性贸易壁垒(TBT)委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。======意义和用途====== 4.1 本规范供参与下水道建设和其他利用柔性热塑性管道的重力流应用的设计者和规范者、安装承包商、监管机构、业主和检验机构使用。与任何标准实践一样,可能需要针对特定的工作条件或特殊的当地或区域条件进行修改。关于在具体项目的合同文件中列入这种做法的建议见 附录X2 .
1.1 This practice provides recommendations for the installation of buried thermoplastic pipe used in sewers and other gravity-flow applications. These recommendations are intended to ensure a stable underground environment for thermoplastic pipe under a wide range of service conditions. However, because of the numerous flexible plastic pipe products available and the inherent variability of natural ground conditions, achieving satisfactory performance of any one product may require modification to provisions contained herein to meet specific project requirements. 1.2 The scope of this practice necessarily excludes product performance criteria such as minimum pipe stiffness, maximum service deflection, or long term strength. Thus, it is incumbent upon the product manufacturer, specifier, or project engineer to verify and assure that the pipe specified for an intended application, when installed according to procedures outlined in this practice, will provide a long term, satisfactory performance according to criteria established for that application. A commentary on factors important in achieving a satisfactory installation is included in Appendix X1 . Note 1: Specific paragraphs in the appendix are referenced in the body of this practice for informational purposes. Note 2: The following ASTM standards may be found useful in connection with this practice: Practice D420 , Test Method D1556/D1556M , Method D2216 , Specification D2235 , Test Method D2412 , Specification D2564 , Practice D2657 , Practice D2855 , Test Methods D2922 , Test Method D3017 , Practice F402 , Specification F477 , Specification F545 , and Specification F913 . Note 3: Most Plumbing Codes and some Building Codes have provisions for the installation of underground “building drains and building sewers.” See them for plumbing piping applications. 1.3 Units— The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 4.1 This practice is for use by designers and specifiers, installation contractors, regulatory agencies, owners, and inspection organizations who are involved in the construction of sewers and other gravity-flow applications that utilize flexible thermoplastic pipe. As with any standard practice, modifications may be required for specific job conditions or for special local or regional conditions. Recommendations for inclusion of this practice in contract documents for a specific project are given in Appendix X2 .
分类信息
关联关系
研制信息
归口单位: F17.62
相似标准/计划/法规