首页 馆藏资源 标准快讯 标准数字化 呈缴征集 标准服务 关于我们
作废 ASTM A926-03(2014)
到馆提醒
收藏跟踪
购买正版
Standard Test Method for Comparing the Abrasion Resistance of Coating Materials for Corrugated Metal Pipe (Withdrawn 2016) 比较波纹金属管材涂层材料耐磨性的标准试验方法(2016年)
发布日期: 2014-08-01
废止日期: 2016-06-20
1.1 本试验方法涵盖了使用推移质磨损试验机比较波纹金属管涂层、铺设和衬里材料的程序。该程序试图模拟水流通过波纹金属管携带的石头、砾石和沙子的效果。 1.2 以英寸-磅为单位的数值应视为标准值。括号中给出的国际单位仅供参考。 1.3 本标准并非旨在解决与其使用相关的所有安全问题(如有)。本标准的用户有责任在使用前制定适当的安全和健康实践,并确定监管限制的适用性。 ====意义和用途====== 4.1 本试验方法提供了一种确定磨损率(重量和计算的平均厚度损失)的方法,当比较材料、涂层、铺面或衬里时,这些材料将在试验条件下承受磨料床荷载。 在处理涵洞、雨水管和污水管应用时,认识到该信息的重要性,尽管由于坡度较平坦,推移质比涵洞小,后两个通常没有相同的磨损程度。具体来说,无论使用何种材料,这些类型管道的内底都可能暴露在含有磨料床荷载或固体颗粒的水流中,从而导致管壁磨损。 4.2 通过使材料在具有由细骨料和粗骨料组成的受控推移质装药的推移质磨耗机中在指定时间内磨损,可以建立材料之间阻力的比较。 4.3 本试验方法不模拟磨料撞击波纹上游面的效果,这对于未完全填充波纹的涂层材料来说是典型的。 注1: 注意事项: 该试验方法使用特定的定量值来鼓励重复结果,不考虑变化的推移质特性、水沙比、速度、时间或实际现场条件,以及暴露边缘对层压板的影响。 由于这些和其他变量,用户必须非常小心地将一个测试结果与另一个进行比较。
1.1 This test method covers a procedure for comparing materials used for coating, paving and lining corrugated metal pipe by use of a bed load abrasion testing machine. The procedure attempts to simulate the effect of stone, gravel and sand carried by a stream through corrugated metal pipe. 1.2 The values stated in inch-pound units are to be regarded as standard. The SI units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ====== Significance And Use ====== 4.1 This test method provides a means of determining an abrasion rate (weight and calculated average thickness loss) when comparing materials, coatings, pavings, or linings under test conditions that will be subjected to abrasive bed loads. The importance of this information is recognized when dealing with culverts, storm and sanitary sewer applications, although the last two generally do not have the same degree of abrasion due to the flatter slopes and less bed loads than culverts. Specifically, the invert of these types of pipe, regardless of the material used, can be exposed to flows containing abrasive bed loads or solid particulates that cause wearing of the pipe wall. 4.2 By subjecting materials to wear in the bed load abrasion machine with a controlled bed load charge made up of fine aggregate and coarse aggregate over a specified period, a comparison of the resistance between materials can be established. 4.3 This test method does not simulate the effect of abrasive material striking the upstream face of corrugations, as would be typical for coating materials which do not completely fill the corrugations. Note 1: Caution: This test method uses specific quantitative values to encourage repetitive results and does not consider varying bed load characteristics, ratio of water to bed load, velocity, time or actual field conditions, and the effect of exposed edges on laminates. The user must use extreme care in comparing one test result to another because of these and other variables.
分类信息
关联关系
研制信息
归口单位: A05.17
相似标准/计划/法规
现行
ASTM D968-25
Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive
有机涂层耐磨性的标准试验方法
2025-05-01
现行
ASTM D4060-25
Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
用泰伯研磨机测定有机涂层耐磨性的标准试验方法
2025-01-15
现行
KS D 0284(2020 Confirm)
강관 코팅재의 내마모 시험
管道涂料耐磨性的标准试验方法
2005-12-27
现行
KS D 0284(2025 Confirm)
강관 코팅재의 내마모 시험
管道涂层耐磨性的标准试验方法
2005-12-27
现行
KS D 0284(2025 Confirm)
강관 코팅재의 내마모 시험
管道涂层耐磨性的标准试验方法
2005-12-27
现行
ASTM G6-07(2024)
Standard Test Method for Abrasion Resistance of Pipeline Coatings
管道涂层耐磨性的标准试验方法
2024-06-01
现行
ASTM B1023-22
Standard Test Method for Abrasion Resistance of Hard Anodic Coatings by a Taber-Type Abraser
用泰伯型磨蚀机测定硬质阳极涂层耐磨性的标准试验方法
2022-08-01
现行
ASTM D8380-21(2026)
Standard Test Method for Dry Abrasion Resistance of Hydrophobic and Omniphobic Coatings
憎水和泛憎水涂层的干耐磨性的标准试验方法
2026-02-01
现行
BS EN 13523-16-2004
Coil coated metals. Test methods-Resistance to abrasion
线圈涂层金属 测试方法
2004-11-25
现行
QB/T 2702-2005
镀膜眼镜镜片耐磨擦测试方法
Test method of abrasion-resistance for coating of spectacles lenses
2005-03-19
现行
ASTM F1978-22
Standard Test Method for Measuring Abrasion Resistance of Metallic Thermal Spray Coatings by Using the Taber Abraser
用泰伯磨耗器测量金属热喷涂涂层耐磨性的标准试验方法
2022-10-01
现行
ASTM D6037-26
Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings
高光泽涂料的耐磨耐磨性的标准测试方法
2026-06-01
现行
ASTM D6279-26
Standard Test Method for Rub Abrasion Mar Resistance of High Gloss Coatings
高光泽涂料的摩擦磨损耐磨性的标准测试方法
2026-06-01
现行
ASTM D3389-21
Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Abrader)
涂层织物耐磨性的标准测试方法(旋转平台磨床)
2021-05-01
现行
HG/T 4303-2012
表面硬化聚酯薄膜 耐磨性测定方法
Test method of resistance to abrasion for hard-coating polyester film
2012-05-24
现行
ASTM F735-22e1
Standard Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using the Oscillating Sand Method
用振荡砂法测定透明塑料和涂层耐磨性的标准试验方法
2022-05-01
现行
UNE-EN 13523-16-2005
Coil coated metals - Test methods - Part 16: Resistance to abrasion
线圈涂层金属.试验方法.第16部分:耐磨性
2005-07-06
现行
DIN EN 13523-16-2005-02
Bandbeschichtete Metalle - Prfverfahren - Teil 16: Widerstandsfhigkeit gegen Abrieb
线圈涂层金属.试验方法.第16部分:耐磨性;德文版EN 13523-16:2004
2005-02-01
现行
BS 3424-24-1990
Testing coated fabrics-Methods 27A and 27B. Methods for determination of abrasion resistance
测试涂层织物 方法27A和27B 耐磨性测定方法
1990-10-31
现行
ASTM D7255-22e1
Standard Test Method for Abrasion Resistance of Leather (Rotary Platform, Abraser Method)
皮革耐磨性的标准试验方法(旋转平台 研磨机法)
2022-04-01