1.1 本试验方法包括稀释沥青的蒸馏试验。 1.2 以国际单位制或英寸磅单位表示的数值应单独视为标准。每个系统中规定的值可能不是完全相等的；因此，每个系统应独立使用。将两个系统的值结合起来可能会导致不符合标准。 1.3 本标准并不旨在解决与其使用相关的所有安全问题（如有）。本标准的使用者有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.4 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。 ====意义和用途====== 4.1 该程序测量稀释沥青中挥发性成分的含量。蒸馏后残留物的性质不一定是原始混合物中使用的沥青的特征，也不一定是现场施用稀释沥青后任何特定时间可能留下的残留物的特征。稀释沥青中有机硅的存在可能会在残留物被倒入残留物容器后通过延缓挥发性物质的损失来影响蒸馏残留物。 注1: 本标准产生的结果的质量取决于执行程序的人员的能力以及所用设备的能力、校准和维护。符合规范标准的机构 D3666 通常被认为能够胜任和客观的测试、取样、检查等。本标准的用户应注意遵守规范 D3666 单独使用并不能完全确保可靠的结果。可靠的结果取决于许多因素；遵循规范的建议 D3666 或者一些类似的可接受的指导方针提供了评估和控制其中一些因素的手段。

1.1 This test method covers a distillation test for cutback asphalts. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 4.1 This procedure measures the amount of the more volatile constituents in cutback asphalt. The properties of the residue after distillation are not necessarily characteristic of the asphalt used in the original mixture, nor of the residue which may be left at any particular time after field application of the cutback asphalt. The presence of silicone in the cutback asphalt may affect the distillation residue by retarding the loss of volatile material after the residue has been poured into the residue container. Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.